How to Do a Door Lock Change
Change your door lock is an easy and inexpensive way to increase the security of your home. This process isn't for everyone. It requires a certain amount of skill and patience.
The cylinder is located within the knob's body. The cylinder recognizes the key once it's put into the lock.
Removal of the old lock
First, you must remove the lock that was previously in place. This is a relatively simple process, but there are a few things to remember. First, ensure that your new lock is the correct size for the door you have. This will ensure that it fits snugly and does not leave a gap around the deadbolt plug or latch.
After you have removed the latch plate, you'll need to look for two screws or bolts on the inside of the casing that hold the casing in place with the two halves of the lock. Take these screws off using a screwdriver before removing the lock from the door. If you have a mortise locking system, there is an anchor screw that connects the handle to the spindle. Use a screwdriver to unscrew this screw, then pull out the doorknobs.
Remove the deadbolt and latch plug from the door jamb. Install the new lock. If you're replacing a mortise you should take a measurement of the distance between the lock case and your door's edge to ensure that your new lock fits.
Several reasons might prompt you to replace the door lock, including believing that someone else has the key, or you are welcoming the arrival of a new roommate. In any event, you could save money by taking the lock off yourself, rather than hiring an expert to do it. The process is easier than many people think, and it can be completed in a few minutes.
Remove the handle and trim of your door. Then, pull the trim loose using a screwdriver that is flat. You should be able twist off the majority of it. In some cases you might be able to remove the handles completely. Then, check the handle for a small pinhole on the interior side and insert a straightened clip into it. This will trigger the release mechanism and allow you to take the handle from the door. Then, look for another small tab in the interior of the lock and push it using a flat screwdriver. Once the spindle has been removed, you can then remove the cylinder and the housing.
The process of selecting a new lock
When it comes to choosing a new lock there are a lot of options. Take a look at the various types of locks and choose one that fits the design of your door. Consider the backset, which is the distance between the edge and the center of lock hole. Also, think about the cross bore, a tiny hole that is located at the edge of your door's frame. Also, make sure to select a lock that is able to be able to fit the door's thickness and swing.
Most door locks have been graded by BHMA and the American National Standards Institute to give you an idea of how they will withstand use and how difficult they are to pick or disable. A lock grade 3 might be ideal for a peaceful apartment building in the countryside, whereas locks that are grade 1 could be better suited to a busy street near a storefront.
Most smart door locks need a digital code to open. If you're concerned about security breaches or hacking seek out a professional locksmith or the local police department for assistance.
Replace the cylinder
It is easy to replace damaged or broken doors lock cylinder by doing an easy DIY project. The key is to choose the right cylinder, and follow the directions that come with it. The first step is to take off the knob or handle, in the event that one is present and then remove the trim around the base of the lock cylinder with the aid of a screwdriver. Once the trim has been removed, you will be able to access the screws that keep the cylinder in place and remove them using a flathead screwdriver. The cylinder is then gently removed from the door.
Before installing the new cylinder, you must make sure it's the correct length for the door you are using. With a tape measure, measure the distance between the center of the cylinder and the right and left sides. Buy a new cylinder that has the same measurements. This will help prevent cylinder snapping, which could happen when the door is kicked in or when the key is stuck inside.
If you have a replacement cylinder, insert it in the door and turn the key. This will align the cylinder with the carrier which is typically on the outside of your lock. Then, you can loosen the set screw which should be just a few turns inside the head. You will also need to loosen the screw on the door's edge that fastens the case, if there is one.
After you have removed the lock cylinder after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. Installing click here. that connects the cylinder to an indicator stem for a lock is also important. You can do this by pulling three tabs on the back of the cylindrical with needle-nosed pliers. Then, you can attach the second bracket to the back of the cylinder. You should then reinstall the latch plate and strike plate, along with the retaining rings that are fixed to the top of the lock cylinder.
Installing a new lock
Start by measuring the door's width if you are replacing a lock that is already in use. Most residential locksets are designed to fit a door thickness of 1 3/8 to 1 3/4 inches. If your door is more thick, you will need a thick door kit that includes longer screws, a longer tail piece (for door knobs) or spindle extension (for deadbolts).
Most locks come with a detailed instruction booklet to help you install the new hardware. Read the instructions carefully before beginning the process to ensure that you've followed all of the necessary steps. The guide will give you a good idea of the amount of skill that is required to complete the task. If you're replacing a lock for the first time, you may consider asking a more experienced friend for assistance.
Before installing the new lock it's an excellent idea to put cover the openings with tape the old hardware. This will stop screws from slipping through the holes, and protect any tiles you might have installed. It also helps prevent possible damage caused by rust, grime, dirt and. SECURAM Touch comes with a strip painter's tape that is intended to be used for this purpose, but you can also use gaffer's tape as well as masking tape when you have it.
After you have removed the screws that hold the lock's inner half to the outside and remove the lock immediately. It's important to do this as quickly as possible to avoid the lock from accidentally closing on itself and damaging the mechanism.
If the new lock comes with an internal latch bolt, insert the new latch bolt into the upper cross bore. Make sure to place it in the proper position, which is marked by an arrow. Then, place the latch plate over the bolt and secure it in the correct position.
Screw the deadbolt to the jamb of the door. Test the deadbolt by throwing it a few times to ensure that it is extended all the way through the strike plate and is fully secure. If you're using an electronic smart lock, be sure to follow the included instructions for programming it. This requires downloading an app, creating an email address, verifying your identity, then accessing the wireless network to add your device.